Cookie Img
Back to top
   Call Me Free Offline Send SMS Send Inquiry
                          Home » Products » Devcon Epoxy Putties » Devcon Aluminum Putty F

                          Devcon Aluminum Putty F

                          Devcon Aluminum Putty F
                          Devcon Aluminum Putty F
                          Product Code : DAPF
                          Brand Name : Devcon
                          Product Description

                          Devcon Aluminum Putty F

                          Description : Devcon Aluminum -filled epoxy putty for dependable non rusting repairs to aluminum castings, machinery, and equipment widely used in HVAC applications.

                          Intended Use : Devcon Aluminum Putty is a Patch for aluminum castings; make jigs, dies, and holding fixtures.

                          Product features : Devcon Aluminum Putty Can be machined, drilled, or tapped using conventional metalworking tools Bonds to aluminum, concrete, and many other metals Fills voids or pores in castings.

                          Limitations : Devcon Aluminum Putty is Not recommended for long term exposure to concentrated acids and organic solvents.

                          Typical Physical Properties : Technical data should be considered representative or typical only and should not be used for specification purposes Cured 7 days @ 75 Degrees Farenheight.

                          Color Aluminum

                          Mix Ratio by Volume - 4:1

                          Mix Ratio by Weight - 9:1

                          % Solids by Volume 100

                          Pot Life @ 75degrees 60 min

                          Specific Volume 17.5 in.(3) /lb

                          Cured Shrinkage 0008 in./in

                          Specific Gravity 1.58 gm/cc

                          Temperature Resistance Wet: 120°F; Dry: 250degrees

                          Coverage/lb 70 sq.in./lb. @ 1/4"

                          Cured Hardness 85D

                          Dielectric Strength 100 volts/mil

                          Dielectric Constant 21.4

                          Adhesive Tensile Shear 2,600 psi

                          Compressive Strength 8,420 psi

                          Modulus Elasticity 8.0 psi x 10(5) in

                          Flexural Strength 6,760 psi

                          Coefficient Degrees Farenheight Thermal Expansion 29 [(in.)/(in). x °F)] x 10(-6)

                          Thermal Conductivity 1.73 [(cal x cm)/(sec x cm(2) x °C)] x 10(-3)

                          Cure Time 16 hrs

                          Recoat Time 10-12 hrs

                          Mixed Viscosity Putty

                          TESTS CONDUCTED :

                          Compressive Strength ASTM D 695

                          Cured Hardness Shore D ASTM D 2240

                          Dielectric Constant ASTM D 150

                          Modulus of Elasticity ASTM D 638

                          Cure Shrinkage ASTM D 2566

                          Adhesive Tensile Shear ASTM D 1002

                          Dielectric Strength, volts/mil ASTM D 149

                          Coef.of Thermal Expansion ASTM D 696

                          Flexural Strength ASTM D 790

                          Thermal Conductivity ASTM C 177

                          Application Instructions : Spread mixed material on repair area and work firmly into substrate to ensure maximum surface contact. Devcon Aluminum Putty F will fully cure in 16 hours, at which time it can be machined, drilled, or painted. FOR BRIDGING LARGE GAPS OR HOLES Place fiberglass sheet, expanded metal, or mechanical fasteners between repair area and Devcon Aluminum Putty F prior to application.

                           

                          JAY AGENCIEZ

                          Contact Us

                          ( *represents compulsory fields )

                          Tips on getting accurate quotes. Please include product name, order quantity, usage, special requests if any in your inquiry.