|Home||» Products||» Devcon Epoxy Putties||» Devcon Underwater Repair Putty wet Surface putty|
Devcon Wet Surface Repair Putty :
Description : Devcon Wet Surface Repair Putty Makes (effective) repairs to metal, concrete, wood surfaces in wet and dry environments.Intended Use: Repairing and refitting pipes, valves, pumps, and tanks. Repair concrete vessels and piping in wet environments.
Devcon Wet Surface Repair Putty product will bond to a wet or damp surface.
Devcon Wet Surface Repair Putty features: Bonds to aluminum, concrete, and many other metals Bonds to ferrous and non-ferrous metals Non-rusting Bonds to wet surfaces Bonds, patches, and seals metals Non-sagging
Typical Physical Properties : Technical data should be considered representative or typical only and should not be used for specification purposes.
Cured 7 days @ 75 degrees farenheight.
For best results, product should be kept and applied at room temperature.
Bronze Putty can be applied when temperatures are between 13 degrees centigrade and 52 degrees centigrade. Spread Bronze Putty over prepared surface with a putty knife. Press firmly to ensure maximum surface contact and avoid trapping air. To bridge large gaps or holes use fibre glass, sheet metal or wire mesh.
Color - Grey
Mix Ratio by Volume 1:1
Mix Ratio by Weight 1.4:1
% Solids by Volume 100
Pot Life @ 75F 45 min.
Specific Volume 17 in.(3)/lb.
Cured Shrinkage 0.0020 in./in.
Specific Gravity 1.4 gm/cc(2)
Temperature Resistance Wet: 120°F; Dry: 250°F
Coverage/lb 68 sq.in./lb. @ 1/4"
Cured Hardness 82 Shore D
Dielectric Strength 150 volts/mils
Dielectric Constant 8.6
Adhesive Tensile Shear 2,685 psi
Compressive Strength 5,625 psi
Modulus of Elasticity 7.5 psi x 10(5) in.
Flexural Strength 4,990 psi
Coefficient of Thermal Expansion 18[(in.)/(in). x °F)] x 10(3)Cure Time 24 hours
Recoat Time 10-12 hours
Mixed Viscosity Putty
For Underwater or submerged repairs consider the following:- Remove all dirt, barnacles, flaking paint, and algae/seaweed from the substrate.- Wipe area with a clean cloth to remove any film on the surface. Obviously you cannot degrease underwater, but wipingand turning a clean cloth often will remove any film on the surface.- Abrade the surface if possible. (Use mechanical means or a file to accomplish.)- The oxidation can be removed by mechanical means, such as water, grit-blasting, or by chemical means.- Make the repair as soon as possible to avoid surface contamination.
Ammonia -Very good, Chlorinated Solvent - Poor, Hydrochloric 10% - Fair, Kerosene - Very good, Methanol - Poor , Sodium Hydroxide 10% - Very good, Sulfuric 10% - Fair, Toluene - Very good,
Devcon Titanium Putty, Devcon Plastic Steel Putty, Devcon Epoxy Putty, Plastic Steel Putty, Devcon Epoxy, Maintenance repair and Overhaul, INDUSTRIAL EPOXY PUTTIES, 180 Degrees Centigrade, ON LINE LEAK ARRESTOR, DEVCON, EPOXY PUTTY, BRUSHABLE CERAMIC, TITANIUM PUTTY, STEEL PUTTY, HIGH TEMPERATURE, Wet Surface Putty, Abrasion Resistant Putty, Under water Putty, Devcon Plastic Steel Putty, Devcon 5 Minutes Epoxy Putty, Devcon 5 Minute Epoxy Putty, Devcon Stainless Steel Putty, Devcon Metal Magic Bond, Devcon Aluminum Putty, Machinable Putty, Devcon Plastic Steel 5 Min Putty (SF), Devcon Titanium Putty, Devcon Brushable Ceramic Blue / Red, Devcon Flexane 80, Aquafix, Aquafix Pipe repair kit, Transformer Oil leak Sealant, Online Oil Leak Sealant, Pipe Leak Sealant, Metal Repair, Metal rebuilding